Air King DRLC707 Podręcznik Użytkownika Pobierz pdf

Model DRLC707

Installation Instructions

and

User Guide

Important Safety Instructions

CAUTION: The equipment covered by these instructions should be installed and

serviced only by competent personnel utilizing proper safety practices and procedures.

These instructions are written for such personnel and are not intended as a substitute

for adequate training and experience in safe procedures for this type of equipment.

Warning: Disconnect the power at service panel before beginning this installation.

Caution: To reduce the risk of fire and to properly exhaust air, be sure to duct air

outside. Do not vent exhaust air into spaces within walls or ceilings, or into attics,

crawl spaces, or garages.

Acceptable for use over tub or shower when installed in a GFCI protected branch

circuit.

Warning: To reduce the risk of fire or electric shock, do not use this fan with any

solid-state speed control device.

Warning: To reduce the risk of fire or electric shock or injury to persons, observe

the following:

a) Use this unit only in the manner intended by the manufacturer. If you have any

questions, please contact the manufacturer.

b) Before servicing or cleaning unit, switch power to off at service panel and lock

the service disconnecting means to prevent power from being switched on

accidentally. When the service disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag, to the service panel.

c) Do not install this fan in a ceiling thermally insulated to a value greater than R-

40.

d) Installation work and electrical wiring must be done by qualified, competent,

trained person(s) in accordance with all applicable codes and standards using

proper safety practices, including fire-related construction.

e) Sufficient air is needed for proper combustion and exhausting of gases through

the flue (chimney) of fuel burning equipment to prevent back drafting. Follow

the heating equipment manufacturer’s guideline and safety standards such as

those published by the National Fire Protection Agency (NFPA) and the American

Society for Heating, Refrigeration, and Air Conditioning Engineers (ASHRAE),

and the local code authorities.

f) When cutting or drilling into a wall or ceiling, ALWAYS identify hidden electrical

wiring and other hidden utilities in advance, to avoid damage.

g) Ducted fans must always be vented to the outdoors.

f) NEVER place a switch where it can be reached from the tub or shower.

Caution: For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

Warning: Do not use in kitchens.

To ensure the best air and sound performance, it is recommended

that the length of ducting and the number of elbows be kept to

a minimum, and that insulated hard ducting be used. Larger duct

sizes will reduce noise and airflow restriction.

Before beginning this installation remove the fan's venturi assembly,

which is secured in place with one screw through the venturi.

This is a captive screw and will stay installed in the venturi. Keep

the venturi assembly and grill/lens/light reflector assembly in

the carton until needed so they do not get damaged or lost.

Mounting the Housing

Select the best location to mount the housing in the ceiling. This fan will require at least

6" of clearance in the ceiling, and will mount through drywall up to 3/4" thick. The fan can

be mounted directly to the joist using the two mounting tabs on the sides of the housing

or between 16" on center joists using the 4 provided mounting rails. Before cutting or drilling

into any drywall, check the area from above to plan the unit's wiring and duct run. Remember

to keep the duct length and number of elbows to a minimum.

1. Determine the best location for the fan.

2. Select the most convenient electrical knockout and remove it.

3. If the unit is being mounted in existing construction, use the housing as a template to

mark the necessary space on the ceiling to cut out.

4. Locate the housing next to the joist and adjust the height so the housing is level with the finished

ceiling. If the unit is being installed in new construction, use the drywall thickness gauge to line

up the bottom of the joist with the appropriate drywall thickness indicated (fig. 1). Secure the

housing directly to the joist through the two holes and two keyhole slots provided.

5. If mounting the housing between joists install the side rails (fig. 2) on the housing. Position

the housing next to the joist and adjust the height so it is flush with the drywall. Secure the

ends of the slide rails to the joists – you can then move the housing into the final position.

Fig. 1

Fig. 2

READ AND SAVE THESE INSTRUCTIONS

Exhaust Fan

with

Light

Square Oak Trim

bathroomsource

.com

Call 1-800-667-8721 anywhere in the US and Canada -

www.bathroomsource.com

Air King at

bathroom::

accessories

U N L I M I T E D

1 2

Podsumowanie treści

Strona 1 - User Guide

Model DRLC707Installation Instructionsand User GuideImportant Safety InstructionsCAUTION: The equipment covered by these instructions should be instal

Strona 2 - Troubleshooting Guide

DuctingNote: All ducting must comply with local and nationalbuilding codes.1. Connect the ducting to the fan's duct collar. Secure inplace using

Komentarze do niniejszej Instrukcji

Brak uwag

Air King DRLC707 Podręcznik Użytkownika

Przeglądaj online lub pobierz Podręcznik Użytkownika dla Wentylatory domowe Air King DRLC707. Air King DRLC707 User guide Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Wentylatory domowe Air King DRLC707